Kit d'isolation L4H3 Armaflex - Flocons - Liège

Kit d'isolation L4H3 Armaflex - Flocons - Liège

2.722_L4H3
€1,050.49 Inc. VAT

Retrouvez ce qui se fait de mieux pour l'isolation de véhicule aménagé camping-car dans ce kit mixte Armaflex / flocons d'Armaflex pour véhicule L4H3.
Se protéger des variations de température est un impératif pour tout voyageur nomade qui souhaite profiter confortablement de son fourgon aménagé.

Pack products My pack description
Expédié sous 24h

Person cleaning the interior walls of a van with Cleaner Armaflex

Step 2: Insulate walls and ceiling

Unroll the Armaflex ChezMoi 19 mm over the walls and ceiling, starting from the bottom and removing the protective film as you go.

Smooth each section by hand to expel the air, then reinforce the ceiling with mechanical fixings every 500 mm.

Step 1: Prepare the surfaces

Degrease the sheet metal with Cleaner Armaflex, from top to bottom, before any installation. A perfectly clean and dry surface is essential: the slightest trace of grease or dust will prevent the adhesive from holding over time.

Fit your battens and mechanical fixings before the insulation, so as not to compress it once in place

Insulating the ceiling of a van

Insulating wall reinforcements with Armaflex ChezMoi 10mm

Step 3: Treat reinforcements and wheel arches

The Armaflex ChezMoi 10 mm, thinner and more flexible, slides into the uprights, longitudinal beams and wheel arches that the 19 mm cannot conform to.

Cut it with a fresh blade and a 5 mm margin to compensate for irregularities in the sheet metal.

Step 4: Fill the doors with flakes

Fit the Proclima Intello vapour barrier using the adhesive tape, making sure to leave a large enough opening. Inject the Armaflex flakes, and reseal the vapour barrier as you fill. Tamp down lightly to avoid air pockets, but without compressing the material.

Once all the nooks and crannies of the door are filled, finish sealing the vapour barrier with the adhesive tape to block water vapour.

Step 5: Seal the joints

Every joint between two strips of Armaflex ChezMoi, every corner and every cut must be sealed with Tape Armaflex ChezMoi. A single exposed spot is enough to create a cold bridge where condensation builds up, with the risk of corrosion on the sheet metal. Be generous — this is not the time to have a light hand!

Cutting a cork roll to insulate the floor of a van

Cutting a strip of Armaflex from a roll

Step 6: Cover the floor

Apply high-performance spray adhesive to the floor panel, then roll out the 4 mm cork on top. Thin and flexible, it takes up almost no floor height while cutting out the cold rising from the ground.

Once laid, your van is fully insulated — you can move on to the next step of your fit-out!

Pack contents

The most demanding size, insulation that leaves nothing to chance

Armaflex ChezMoi insulates your L4H3 van from floor to ceiling, including the walls and reinforcements.

Yet, on this largest size in the range, it's the doors where everything comes together: Armaflex flakes fill every nook without any cutting required, whatever the shape. Cork insulates the floor, and Armaflex ChezMoi 19mm covers the walls and ceiling.

Quantities already calibrated for this size, adhesives and accessories included.

Compatible with L4H3 vans on the market (Renault Master, Fiat Ducato, Citroën Jumper, Peugeot Boxer, Ford Transit, Mercedes Sprinter, Volkswagen Crafter and equivalents), this kit covers walls, ceiling, doors, wheel arches and floor.

  • Quantities calibrated for an L4H3: no more guesswork or unnecessary offcuts on this large size.
  • No complex cutting on the doors: the flakes conform to every nook, whatever the shape.
  • Armaflex ChezMoi, designed for the van: unlike the older AF, which was designed for construction.
  • Insulation that covers everything: walls, ceiling, doors, wheel arches and floor.
  • No cutting on difficult areas: the flakes are poured and compacted, without millimetre-precise adjustments.

 

L4H3 insulation kit contents

Walls, ceiling and structural reinforcements

 

Doors

 

Wheel arches

  • Armaflex ChezMoi 10 mm self-adhesive (quantity included above)

 

Floor

 

Materials chosen for their role in insulation

Armaflex ChezMoi — the insulation designed for the van

Successor to the Armaflex AF, the ChezMoi uses the same closed-cell technology, in a formulation designed from the outset for van fitting rather than construction. Its integrated vapour barrier means there is no need to add a separate vapour control layer to the walls and ceiling.

  • Role in the kit: walls, ceiling, reinforcements, wheel arches
  • Thickness / packaging: 19 mm (6 m² roll) and 10 mm (10 m² roll)
  • Thermal conductivity (λ): 0.035 W/(m·K)
  • Integrated vapour barrier: closed cells, no separate vapour control layer needed
  • Antimicrobial treatment: Microban®, integrated into the material
  • Service temperature: -50 °C to +85 °C
  • VOC emissions: A+ rating (ISO 16 000)
  • Manufacturer's warranty: 10 years
  • Origin / manufacture: Europe, Armacell technology

 

Armaflex flakes — the loose-fill insulation for impossible nooks

Armaflex flakes offer the same insulating properties as roll Armaflex, in a form that can be poured and conforms to any cavity — a solution for doors and areas that cut panels would be far more complex to cover!

  • Role in the kit: doors
  • Packaging: 5 kg bag
  • Nature: same material as roll Armaflex, in granule form
  • Installation method: poured and lightly compacted into the cavity

 

Cork — the natural floor insulation

Naturally rot-proof and moisture-resistant, cork insulates the floor without adding unnecessary thickness. Its lightness and flexibility make it a simple solution to install with spray adhesive, directly onto the metal sheet.

  • Role in the kit: floor
  • Thickness / packaging: 4 mm (4 m² roll)
  • Moisture resistance: rot-proof, naturally water-resistant
  • Origin / manufacture: natural material

You might also be interested in