Easy-fit Armaflex ChezMoi insulation kit for Volkswagen Transporter L2H2
Easy-fit Armaflex ChezMoi insulation kit for Volkswagen Transporter L2H2
Ready-to-install insulation kit for the Volkswagen Transporter L2H2: 28 m² of self-adhesive Armaflex ChezMoi, with everything you need for installation included.
- 1 roll of Armaflex ChezMoi 10 mm (10 m²)
- 3 rolls of Armaflex ChezMoi 19 mm (18 m²)
- 3 rolls of Tape (15 m × 50 mm)
- 1 Cleaner (1 L bottle)
- 1 pair of gloves and 1 utility knife included free
Integrated vapour barrier, no additional adhesive needed, 10-year manufacturer’s guarantee.
Quantities calculated for the Volkswagen Transporter L2H2, excluding the cab partition.
Insulate your Volkswagen Transporter L2H2 without added adhesive: 28 m² of self-adhesive Armaflex ChezMoi
To convert a Volkswagen Transporter L2H2 into a campervan, this kit brings together self-adhesive Armaflex ChezMoi and everything needed to install it: 1 roll of 10 mm, 3 rolls of 19 mm, 3 rolls of Tape and 1 Cleaner, plus a free pair of gloves and utility knife. No adhesive to buy or spread: the self-adhesive backing sticks directly to the cleaned metal. The quantities are calculated for the Transporter L2H2, excluding the cab partition.
Armaflex ChezMoi is an elastomeric foam made in Europe using Armacell technology. Its self-adhesive backing sticks directly to the cleaned metal, with no additional adhesive needed. Its closed cells also act as a vapour barrier (μ> 7,000): there is no separate vapour control layer to install, and less condensation forms on the metal.
With a thermal conductivity of 0.035 W/(m·K) and an operating range of −50 °C to +85 °C, it insulates against both cold and heat, whether you convert your Transporter into a campervan or keep it as a work van. The A+ rating (ISO 16000, VOC-free) and Microban® antimicrobial treatment integrated into the material matter in a space where you sleep. Its fire performance meets the FMVSS automotive standard, and the manufacturer guarantees the material for 10 years.
The kit is straightforward to use: 10 mm for the floor and pillars, 19 mm for the walls and ceiling, Tape to seal the joins and Cleaner to clean the metal before installation.
Armaflex ChezMoi 19 mm: insulate the walls and ceiling
The 19 mm insulation is the standard thickness for large surfaces. It provides more insulation where space allows: the Transporter’s side walls, doors and ceiling. The kit contains 3 rolls, covering 18 m².
- Thickness: 19 mm
- Pack size: 6 m² roll (6 m × 1 m)
- Thermal conductivity: λ = 0.035 W/(m·K) at 0 °C
- Vapour barrier: integrated, μ> 7,000
- Operating temperature: −50 °C to +85 °C
- Fire performance: FMVSS automotive standard
- Air quality: A+ rating (ISO 16000), VOC-free
- Antimicrobial treatment: Microban® integrated into the material
- Guarantee: 10 years (manufacturer)

Armaflex ChezMoi 10 mm: insulate the floor and pillars
The 10 mm insulation fits where space is tight: the floor, deep structural supports, wheel arches and pillars. It preserves headroom while insulating the metal. The kit contains 1 roll, covering 10 m².
- Thickness: 10 mm
- Pack size: 10 m² roll (10 m × 1 m)
- Thermal conductivity: λ = 0.035 W/(m·K) at 0 °C
- Vapour barrier: integrated, μ> 7,000
- Operating temperature: −50 °C to +85 °C
- Fire performance: FMVSS automotive standard
- Air quality: A+ rating (ISO 16000), VOC-free
- Antimicrobial treatment: Microban® integrated into the material
- Guarantee: 10 years (manufacturer)

Tape, Cleaner, gloves and utility knife: preparation, cutting and sealing joins
Tape seals the joins between the sheets to limit thermal bridges, while Cleaner degreases the metal for good adhesion. The kit contains 3 rolls of Tape, giving you 45 m of tape, and 1 Cleaner. A pair of gloves and a utility knife are included free for handling and cutting the insulation.
- Tape: 15 m × 50 mm adhesive roll; 3 in the kit
- Cleaner: solvent-based Armaflex cleaner, 1 L bottle, applied with a cloth; 1 in the kit
- Gloves: 1 pair, included free with the kit
- Utility knife: 1 utility knife, included free with the kit

Compatibility: Volkswagen Transporter L2H2
The kit is sized for the load area of a Volkswagen Transporter L2H2 panel van, T5, T6 or T6.1 generation: 2,975 mm long, 1,692 mm wide and 1,635 mm high. These dimensions are indicative: measure your vehicle before installation, especially if it has already been converted.
The latest-generation Transporter (T7) is built on a different platform and has a different load area, so this kit is not suitable for it.
Please note: The partition separating the load area from the cab is not included in the surfaces covered by the kit.
As the closed cells of Armaflex ChezMoi already act as a vapour barrier, there is no need for a separate vapour control layer.
Other Transporter sizes: L1H1, L1H2 and L2H1.
How do you install the Armaflex ChezMoi kit in a Volkswagen Transporter L2H2?
Armaflex ChezMoi is self-adhesive: it installs without added adhesive using a few simple tools and requires no specialist skills. Just follow the steps in order. Our blog article on installing Armaflex explains each step in detail.
- Prepare the walls. Identify the areas to insulate. If you plan to fit wooden lining, install your fixing battens first.
- Clean the walls before installation. Dampen a clean cloth with Cleaner and wipe down all the metal: it must be clean and degreased for the adhesive to bond. Cleaner contains a solvent and gives off fumes: wear a mask and work outdoors if possible.
- Mark out. Transfer the dimensions of each area onto the non-adhesive side of the insulation, starting with the floor and pillars (10 mm), then the walls and ceiling (19 mm).
- Cut. Put on the gloves included free and cut the sheets to shape using the utility knife supplied with the kit, or an Armacell knife set if you prefer. The foam cuts cleanly.
- Stick. Peel away the protective film as you go, pressing the sheet onto the metal from the centre outwards to push out any air.
- Seal the joins. Apply Tape over every join between two sheets to limit thermal bridges.
Kit technical specifications
| Specification | Armaflex ChezMoi 10 mm | Armaflex ChezMoi 19 mm |
|---|---|---|
| Quantity in the kit | 1 roll | 3 rolls |
| Area covered by the kit | 10 m² | 18 m² |
| Pack size | 10 m × 1 m | 6 m × 1 m |
| Recommended areas | Floor, pillars | Walls, ceiling |
| Thermal conductivity | λ = 0.035 W/(m·K) at 0 °C | λ = 0.035 W/(m·K) at 0 °C |
| Water vapour resistance | μ> 7,000 | μ> 7,000 |
| Operating temperature | −50 °C to +85 °C | −50 °C to +85 °C |
| Fire performance | FMVSS automotive standard | FMVSS automotive standard |
| Air quality | A+ (ISO 16000), VOC-free | A+ (ISO 16000), VOC-free |
| Antimicrobial treatment | Integrated Microban® | Integrated Microban® |
| Guarantee | 10 years (manufacturer) | 10 years (manufacturer) |
The kit also contains 3 rolls of Tape (15 m × 50 mm), 1 solvent-based Cleaner (1 L bottle), plus 1 pair of gloves and 1 utility knife included free.
Frequently asked questions about insulating a Volkswagen Transporter L2H2
How do I know if my Transporter is an L2H2?
The Transporter panel van comes with a short (L1) or long (L2) wheelbase, and our kits cover both the standard roof (H1) and high roof (H2). Measure the usable floor length and interior height: approximately 2,572 mm for L1 and 2,975 mm for L2, and 1,410 mm for H1 and 1,635 mm for H2.
Do I need DIY experience to install this kit?
No. The insulation is self-adhesive and can be cut with the utility knife included free in the kit: clean, cut, stick, then seal the joins with Tape. Just follow the six steps in the installation section; the video shows you how.
Do I need to add adhesive?
No, Armaflex ChezMoi’s self-adhesive backing sticks directly to the metal. Cleaner is used only to degrease it so the adhesive bonds properly.
Is this kit suitable for a Volkswagen Caravelle?
It is designed for a panel van Transporter being converted into a campervan. The Volkswagen Caravelle is a glazed passenger version with an existing interior trim, so it does not have the same surfaces to insulate: measure the areas you need to cover before choosing your quantities of Armaflex.
Can I double the thickness for very cold conditions?
Yes, you can add a second layer to exposed areas if you drive in very cold conditions. You will need to add rolls of Armaflex ChezMoi 19 mm to the kit.
Armaflex ChezMoi or Armaflex AF: what’s the difference?
Armaflex ChezMoi is the successor to Armaflex AF for vehicle conversions: the same self-adhesive foam, with fire performance in accordance with the FMVSS automotive standard. Our article compares the two ranges point by point.
Is this kit suitable for a Transporter T5, T6 or T6.1?
Yes. Transporter T5, T6 and T6.1 panel vans have the same load area: the L2H2 kit fits all three generations. It is not suitable for the latest-generation Transporter (T7), which is built on a different platform.
Complete the insulation and interior finish of your Volkswagen Transporter L2H2
This kit insulates the metalwork in one go. To go further with environmentally responsible materials, explore our campervan insulation kits.
For the floor, add a roll of 4 mm cork underlay beneath your floor covering: it reduces the feeling of a cold floor and reduces vibrations and road noise. Explore the full cork insulation range.
To cover the insulation, Heode offers wooden lining panels cut to fit the Transporter: side walls and floor for the T5 (2003 to 2015), ceiling and floor for the T6 (2015 to 2019). Find the full range in the Transporter T5 and T6 lining panels category.
To finish the walls, start with a stretch felt sample: you can choose the colour (light grey, dark grey, anthracite, black or beige) in your own van before ordering the van lining felt.
-
Best selling