Easy-fit Armaflex ChezMoi insulation kit for Fiat Scudo L1H1
Easy-fit Armaflex ChezMoi insulation kit for Fiat Scudo L1H1
Ready-to-fit insulation kit for the Fiat Scudo L1H1: 22 m² of self-adhesive Armaflex ChezMoi, with everything you need to install it.
- 1 roll of Armaflex ChezMoi 10 mm (10 m²)
- 2 rolls of Armaflex ChezMoi 19 mm (12 m²)
- 2 rolls of Tape (15 m × 50 mm)
- 1 Cleaner (1 L bottle)
- 1 pair of gloves and 1 utility knife included free
Integrated vapour barrier, no additional adhesive needed, 10-year manufacturer’s warranty.
Quantities calculated for the Fiat Scudo L1H1, excluding the cab bulkhead.
Limit condensation in your Fiat Scudo L1H1: 22 m² of Armaflex ChezMoi
The closed cells of Armaflex ChezMoi act as an integrated vapour barrier (μ> 7 000): applied to the metal bodywork of a Fiat Scudo L1H1, it limits condensation without the need for an additional vapour control layer. This kit contains the quantities calculated for the Scudo L1H1: 1 roll of 10 mm, 2 rolls of 19 mm, 2 rolls of Tape and 1 Cleaner, plus a free pair of gloves and utility knife.
Armaflex ChezMoi is an elastomeric foam, made in Europe using Armacell technology. Its self-adhesive side sticks directly to clean metal bodywork, with no additional adhesive needed. It insulates the entire metal surface, including the ceiling.
With a thermal conductivity of 0,035 W/(m·K) and an operating range of −50 °C to +85 °C, it insulates against both cold and heat, whether you convert your Scudo into a campervan or keep it as a work van. The A+ rating (ISO 16000, VOC-free) and the Microban® antimicrobial treatment built into the material matter in a space where you sleep. Its fire performance meets the automotive FMVSS standard, and the manufacturer guarantees the material for 10 years.
The kit is straightforward to use: the 10 mm goes on the floor and pillars, the 19 mm on the walls and ceiling, the Tape seals the joints, and the Cleaner cleans the metal bodywork before installation.
Armaflex ChezMoi 19 mm: insulate the walls and ceiling
The 19 mm is the standard thickness for larger surfaces. It provides the most insulation where space allows: the Scudo’s side walls, doors and ceiling. The kit contains 2 rolls, covering 12 m².
- Thickness: 19 mm
- Pack size: 6 m² roll (6 m × 1 m)
- Thermal conductivity: λ = 0,035 W/(m·K) at 0 °C
- Vapour barrier: integrated, μ> 7 000
- Operating temperature: −50 °C to +85 °C
- Fire performance: automotive FMVSS standard
- Air quality: A+ rating (ISO 16000), VOC-free
- Antimicrobial treatment: Microban® integrated into the material
- Warranty: 10 years (manufacturer)

Armaflex ChezMoi 10 mm: insulate the floor and pillars
The 10 mm fits where space is tight: the floor, deep structural reinforcements, wheel arches and pillars. It preserves headroom while insulating the metal bodywork. The kit contains 1 roll, covering 10 m².
- Thickness: 10 mm
- Pack size: 10 m² roll (10 m × 1 m)
- Thermal conductivity: λ = 0,035 W/(m·K) at 0 °C
- Vapour barrier: integrated, μ> 7 000
- Operating temperature: −50 °C to +85 °C
- Fire performance: automotive FMVSS standard
- Air quality: A+ rating (ISO 16000), VOC-free
- Antimicrobial treatment: Microban® integrated into the material
- Warranty: 10 years (manufacturer)

Tape, Cleaner, gloves and utility knife: preparation, cutting and joints
The Tape seals the joints between sheets to limit thermal bridges, while the Cleaner degreases the metal bodywork for good adhesion. The kit contains 2 rolls of Tape, providing 30 m of tape, and 1 Cleaner. A pair of gloves and a utility knife are included free for handling and cutting the insulation.
- Tape: 15 m × 50 mm adhesive roll, 2 included in the kit
- Cleaner: solvent-based Armaflex cleaner, 1 L bottle, applied with a cloth, 1 included in the kit
- Gloves: 1 pair, included free with the kit
- Utility knife: 1, included free with the kit

Compatibility: Fiat Scudo L1H1
The kit is sized for the load area of a Fiat Scudo L1H1 panel van from 2007 to 2016: 2 254 mm long, 1 600 mm wide and 1 449 mm high, with 1 245 mm between the wheel arches. These measurements are a guide: measure your vehicle before installation, especially if it has already been converted.
It is also suitable for Citroën Jumpy and Peugeot Expert vans from 2007 to 2016 and the Toyota Proace from 2013 to 2016 in L1H1 form, which share the Scudo’s bodywork.
The Fiat Scudo sold since 2022 shares its bodywork with the current Peugeot Expert and Citroën Jumpy: for this model, choose the Peugeot Expert Standard kit (Scudo Standard) or the Peugeot Expert Long kit (Scudo Maxi).
Please note: The bulkhead separating the load area from the cab is not included in the kit’s coverage.
As the closed cells of Armaflex ChezMoi already act as a vapour barrier, no additional vapour control layer is needed.
Other Scudo sizes: L2H1 and L2H2.
How do I install the Armaflex ChezMoi kit in a Fiat Scudo L1H1?
Armaflex ChezMoi is self-adhesive: it can be installed without additional adhesive, using a few simple tools, and requires no special skills. Just follow the steps in order. Our blog article on installing Armaflex explains each step in detail.
- Prepare the surfaces. Identify the areas to insulate. If you plan to fit wood panelling, install the fixing battens first.
- Clean the surfaces before installation. Moisten a clean cloth with Cleaner and wipe down all the metal bodywork: it must be clean and degreased for the adhesive to bond. Cleaner contains a solvent and gives off fumes: wear a mask and work outdoors if possible.
- Mark out. Mark the dimensions of each area on the non-adhesive side of the insulation, starting with the floor and pillars (10 mm), then the walls and ceiling (19 mm).
- Cut. Put on the free gloves and cut the sheets to shape with the utility knife supplied in the kit, or with an Armacell knife kit if you prefer. The foam cuts cleanly.
- Stick in place. Peel off the protective film as you go, pressing the sheet onto the metal bodywork from the centre outwards to push out any air.
- Seal the joints. Apply Tape over every joint between two sheets to limit thermal bridges.
Kit technical specifications
| Specification | Armaflex ChezMoi 10 mm | Armaflex ChezMoi 19 mm |
|---|---|---|
| Quantity in the kit | 1 roll | 2 rolls |
| Area covered by the kit | 10 m² | 12 m² |
| Pack size | 10 m × 1 m | 6 m × 1 m |
| Recommended areas | Floor, pillars | Walls, ceiling |
| Thermal conductivity | λ = 0,035 W/(m·K) at 0 °C | λ = 0,035 W/(m·K) at 0 °C |
| Water vapour resistance | μ> 7 000 | μ> 7 000 |
| Operating temperature | −50 °C to +85 °C | −50 °C to +85 °C |
| Fire performance | Automotive FMVSS standard | Automotive FMVSS standard |
| Air quality | A+ (ISO 16000), VOC-free | A+ (ISO 16000), VOC-free |
| Antimicrobial treatment | Integrated Microban® | Integrated Microban® |
| Warranty | 10 years (manufacturer) | 10 years (manufacturer) |
The kit also contains 2 rolls of Tape (15 m × 50 mm), 1 solvent-based Cleaner (1 L bottle), plus a free pair of gloves and utility knife.
Frequently asked questions about insulating a Fiat Scudo L1H1
How can I tell if my Scudo is an L1H1?
The 2007 to 2016 Scudo panel van comes with a short (L1) or long (L2) wheelbase, and a standard (H1) or high (H2) roof. Measure the usable floor length and interior height: approximately 2 254 mm for L1 and 2 584 mm for L2, and 1 449 mm for H1 and 1 750 mm for H2.
Do I need DIY experience to install this kit?
No. The insulation is self-adhesive and can be cut with the utility knife included free in the kit: clean, cut, stick, then seal the joints with Tape. Just follow the six steps in the installation section; the video shows you how.
Do I need to add adhesive?
No, the self-adhesive side of Armaflex ChezMoi sticks directly to the metal bodywork. The Cleaner is used only to degrease it so the adhesive bonds properly.
Is this kit suitable for a Fiat Scudo Combi?
The kit is designed for a panel van Scudo being converted into a campervan. The Fiat Scudo Combi, a glazed passenger version with an existing interior trim, does not have the same areas to insulate: measure the areas you need to cover before choosing how much Armaflex to buy.
Can I double the thickness for very cold conditions?
Yes, you can layer two sheets in exposed areas if you drive in very cold conditions. You will need to add rolls of Armaflex ChezMoi 19 mm to the kit.
Armaflex ChezMoi or Armaflex AF: what’s the difference?
Armaflex ChezMoi is the successor to Armaflex AF for vehicle conversions: the same self-adhesive foam, with fire performance in accordance with the automotive FMVSS standard. Our article compares the two ranges point by point.
Is this kit suitable for the Fiat Scudo sold since 2022?
No. This kit is calculated for the 2007 to 2016 Scudo. The current Scudo shares its bodywork with the Peugeot Expert: choose the Peugeot Expert Standard kit for a Scudo Standard, or the Peugeot Expert Long kit for a Scudo Maxi.
Complete the insulation and finish of your Fiat Scudo L1H1
This kit insulates the metal bodywork in one go. To go further with eco-friendly materials, explore our campervan insulation kits.
For the floor, add a layer of 4 mm cork underlay on a roll beneath your floor covering: it reduces the cold-floor effect and reduces vibrations and road noise. Explore the full cork insulation range.
For the wall finish, start with a stretch carpet lining sample: you can choose the colour (light grey, dark grey, anthracite, black or beige) in your van before ordering the van carpet lining.
-
Best selling