Easy insulation kit Armaflex ChezMoi Ford Transit Custom L2H2

New

Easy insulation kit Armaflex ChezMoi Ford Transit Custom L2H2

2.567_FTC_L2H2
€486.76 Inc. VAT

Ready-to-fit insulation kit for the Ford Transit Custom L2H2: 28 m² of self-adhesive Armaflex ChezMoi, with everything you need to fit it.

  • 1 roll of Armaflex ChezMoi 10 mm (10 m²)
  • 3 rolls of Armaflex ChezMoi 19 mm (18 m²)
  • 3 rolls of Tape (15 m × 50 mm)
  • 1 Cleaner (1 L bottle)
  • 1 pair of gloves and 1 utility knife included free

 

Integrated vapour barrier, no extra glue needed, 10-year manufacturer’s guarantee.

Quantities calculated for the Ford Transit Custom L2H2, excluding the cab partition.

Pack products My pack description
Pack contents

28 m² of Armaflex ChezMoi calculated to insulate your Ford Transit Custom L2H2

This kit brings together all the Armaflex ChezMoi you need to insulate a Ford Transit Custom L2H2 for a campervan conversion: 1 roll of 10 mm, 3 rolls of 19 mm, 3 rolls of Tape and 1 Cleaner, with a pair of gloves and a utility knife included free. The quantities are calculated for the Transit Custom L2H2: order everything at once, with no surface area to estimate or extra products to add.

Armaflex ChezMoi is an elastomeric foam made in Europe using Armacell technology. Its self-adhesive side sticks directly to cleaned metalwork, with no extra glue needed. The closed cells also act as a vapour barrier (μ> 7,000): there is no separate vapour control layer to fit, and less condensation forms on the metalwork.

With a thermal conductivity of 0.035 W/(m·K) and an operating range of −50 °C to +85 °C, it insulates against both cold and heat, whether you convert your Transit Custom into a campervan or keep it as a work van. Its A+ air-quality rating (ISO 16000, VOC-free) and Microban® antimicrobial treatment integrated into the material matter in a space where you sleep. Its fire performance meets the FMVSS automotive standard, and the manufacturer guarantees the material for 10 years.

The kit is straightforward to use: the 10 mm insulation goes on the floor and pillars, the 19 mm insulation on the walls and ceiling, the Tape seals the joints, and the Cleaner cleans the metalwork before fitting.

 

Armaflex ChezMoi 19 mm: insulating the walls and ceiling

The 19 mm insulation is the standard thickness for large surfaces. It provides the most insulation where space allows: on the Transit Custom’s side walls, doors and ceiling. The kit contains 3 rolls, covering 18 m².

  • Thickness: 19 mm
  • Pack size: 6 m² roll (6 m × 1 m)
  • Thermal conductivity: λ = 0.035 W/(m·K) at 0 °C
  • Vapour barrier: integrated, μ> 7,000
  • Operating temperature: −50 °C to +85 °C
  • Fire performance: FMVSS automotive standard
  • Air quality: A+ rating (ISO 16000), VOC-free
  • Antimicrobial treatment: Microban® integrated into the material
  • Guarantee: 10 years (manufacturer)

 

Where to fit each type of insulation: cross-section diagram of a campervan

 

Armaflex ChezMoi 10 mm: insulating the floor and pillars

The 10 mm insulation fits where space is tight: the floor, deep reinforcement sections, wheel arches and pillars. It preserves interior height while insulating the metalwork. The kit contains 1 roll, covering 10 m².

  • Thickness: 10 mm
  • Pack size: 10 m² roll (10 m × 1 m)
  • Thermal conductivity: λ = 0.035 W/(m·K) at 0 °C
  • Vapour barrier: integrated, μ> 7,000
  • Operating temperature: −50 °C to +85 °C
  • Fire performance: FMVSS automotive standard
  • Air quality: A+ rating (ISO 16000), VOC-free
  • Antimicrobial treatment: Microban® integrated into the material
  • Guarantee: 10 years (manufacturer)

 

Cutting an Armaflex ChezMoi sheet to size before sticking it down

 

Tape, Cleaner, gloves and utility knife: preparation, cutting and joints

The Tape seals the joints between the sheets to limit thermal bridging, while the Cleaner degreases the metal for good adhesion. The kit contains 3 rolls of Tape, providing 45 m of tape, and 1 Cleaner. A pair of gloves and a utility knife are included free for handling and cutting the insulation.

  • Tape: 15 m × 50 mm adhesive roll, 3 included in the kit
  • Cleaner: solvent-based Armaflex cleaner, 1 L bottle, applied with a cloth, 1 included in the kit
  • Gloves: 1 pair, included free with the kit
  • Utility knife: 1, included free with the kit

 

Joint between two sheets of Armaflex covered with Tape

 

Compatibility: Ford Transit Custom L2H2

The kit is sized for the load area of a 2012 to 2023 Ford Transit Custom L2H2 panel van: 2,921 mm long, 1,775 mm wide and 1,778 mm high, with 1,351 mm between the wheel arches. These measurements are indicative: measure your vehicle before fitting, especially if it has already been converted.

The Transit Custom sold since 2024 has a different load area: this kit is sized for the 2012-2023 generation.

Please note: The partition separating the load area from the cab is not included in the surface areas covered by the kit.

Because the closed cells of Armaflex ChezMoi already act as a vapour barrier, no additional vapour control layer is needed.

Other Transit Custom sizes: L1H1, L1H2 and L2H1.

 

How do I fit the Armaflex ChezMoi kit in a Ford Transit Custom L2H2?

Armaflex ChezMoi is self-adhesive: it can be fitted without glue using a few simple tools, and requires no special skills. Just follow the steps in order. Our blog article on fitting Armaflex explains each step in detail.

  1. Prepare the walls. Identify the areas to insulate. If you plan to fit wood panelling, install your fixing battens first.
  2. Clean the walls before fitting. Dampen a clean cloth with Cleaner and wipe down all the metalwork: it must be clean and free of grease for the adhesive to stick. Cleaner contains a solvent and gives off fumes: wear a mask and work outdoors if possible.
  3. Mark out. Transfer the measurements for each area onto the non-adhesive side of the insulation, starting with the floor and pillars (10 mm), then the walls and ceiling (19 mm).
  4. Cut to size. Put on the gloves included free and cut the sheets to shape with the utility knife in the kit, or with an Armacell knife set if you prefer. The foam cuts cleanly.
  5. Stick in place. Peel off the protective film gradually, pressing the sheet onto the metalwork from the centre outwards to push out any air.
  6. Seal the joints. Apply Tape over every joint between two sheets to limit thermal bridging.

 

 

Kit specifications

Specification Armaflex ChezMoi 10 mm Armaflex ChezMoi 19 mm
Quantity in the kit 1 roll 3 rolls
Area covered by the kit 10 m² 18 m²
Pack size 10 m × 1 m 6 m × 1 m
Recommended areas Floor, pillars Walls, ceiling
Thermal conductivity λ = 0.035 W/(m·K) at 0 °C λ = 0.035 W/(m·K) at 0 °C
Water vapour resistance μ> 7,000 μ> 7,000
Operating temperature −50 °C to +85 °C −50 °C to +85 °C
Fire performance FMVSS automotive standard FMVSS automotive standard
Air quality A+ (ISO 16000), VOC-free A+ (ISO 16000), VOC-free
Antimicrobial treatment Integrated Microban® Integrated Microban®
Guarantee 10 years (manufacturer) 10 years (manufacturer)

 

The kit also contains 3 rolls of Tape (15 m × 50 mm), 1 solvent-based Cleaner (1 L bottle), plus 1 pair of gloves and 1 utility knife included free.

 

Frequently asked questions about insulating a Ford Transit Custom L2H2

How can I tell if my Transit Custom is an L2H2?

The Transit Custom panel van comes with a short (L1) or long (L2) wheelbase and a standard (H1) or high (H2) roof. Measure the usable floor length and interior height: approximately 2,554 mm for L1 and 2,921 mm for L2, and 1,406 mm for H1 and 1,778 mm for H2.

 

Do I need DIY experience to fit this kit?

No. The insulation is self-adhesive and can be cut with the utility knife included free in the kit: clean, cut, stick, then seal the joints with Tape. The six steps in the fitting section are all you need, and the video shows you how.

 

Do I need to add glue?

No, the self-adhesive side of Armaflex ChezMoi sticks directly to the metalwork. The Cleaner is used only to degrease it so the adhesive bonds properly.

 

Is this kit suitable for a Ford Tourneo Custom?

It is designed for a Transit Custom panel van being converted into a campervan. The Ford Tourneo Custom is a glazed passenger version with interior trim already fitted, so it does not have the same areas to insulate: measure the areas you need to cover before deciding how much Armaflex to buy.

 

Can I double the thickness for very cold conditions?

Yes, you can layer two sheets in exposed areas if you drive in very cold conditions. You will need to add rolls of Armaflex ChezMoi 19 mm to the kit.

 

Armaflex ChezMoi or Armaflex AF: what’s the difference?

Armaflex ChezMoi is the successor to Armaflex AF for vehicle conversions: the same self-adhesive foam, with fire performance tested to the FMVSS automotive standard. Our article compares the two ranges point by point.

 

Is this kit suitable for the Transit Custom sold since 2024?

This kit is sized for the 2012 to 2023 Transit Custom. The current generation has a different body: measure your vehicle before ordering.

 

Complete the insulation and finish of your Ford Transit Custom L2H2

This kit insulates the metalwork in one go. For more options using eco-friendly materials, explore our campervan insulation kits.

For the floor, add a layer of 4 mm cork underlay on a roll beneath your floor covering: it reduces the feeling of a cold floor and reduces vibrations and road noise. Explore our full cork insulation range.

To finish the floor, Heode offers a non-slip floor panel cut to fit the 2012 to 2023 Transit Custom, ready to fit over the insulation. Find our lining panels in the 2012 to 2023 Ford Custom category.

For the wall finish, start with a sample of stretch carpet lining: you can choose the colour (light grey, dark grey, anthracite, black or beige) inside your van before ordering the van carpet lining.